Installing. Tub Surround - How to Install a Tub Surround. Press the panel firmly into the corner so that it sticks on one side. When all looks well, press down the remaining side until the tape takes hold. Finish by running a hand over the entire panel, top to bottom, to make sure the adhesive makes full contact with the wall. Install the second corner in similar fashion. Step 1. 2: Installing the Panels.
Measure the distance between the corners and mark the centerline on the tub. Then, lay the middle panel on sawhorses and mark its center on the bottom.
Turn the panel over and apply adhesive to the perimeter, behind the soap dishes and in a large, looping pattern across the middle. Pull the backing paper from the perimeter tape, set the panel on the tub and carefully align the two center marks. Finally, bend the bottom of the panel to the wall, sticking it in place. Gradually stick the rest of the panel, working from the bottom up. Step 1. 3: Plumbing Cutouts. The side panel opposite to the spout will go on like the center panel, but will be aligned with the vertical reference line you've drawn. The plumbing- wall panel, however, requires a little more attention.
Begin by laying the panel on two 2 x 4s resting on sawhorses. At the tub, measure from the reference line to the center of the spout pipe. Then, measure from the top of the tub to the center of the spout pipe and do the same with the faucet. If the faucet's trim plate is recessed, like ours, you'll also need to take its measurement, sizing the cut to fit the plate's concave center.
Step 1. 4: Plumbing Cutouts. Transfer each measurement to the panel, one at a time, and double- check each one. Use a 1- in. bit to bore the spout pipe opening. Then, use the same bit to bore a starter hole for the faucet. Enlarge the opening with a sabre saw to accommodate the recessed trim plate. Of course, if your trim plate is not recessed, a 2- or 3- in.
Step 1. 5: Plumbing Cutouts. Dry fit the panel and make minor adjustments if needed.
When you're sure everything fits, apply adhesive to the perimeter of the panel, across its center and around each opening. Finally, slide the panel over the spout pipe and faucet and arch the bottom of the panel against the wall. Apply gradual upward pressure until the entire panel is stuck in place.
Finish by installing the tub spout and faucet trim. Step 1. 6: Waterproofing. Manufacturers often supply a tube of latex adhesive caulk. Use it to fill the gap between the walls and the panels around the perimeter, including the tops of the panels. For the fixture seams, at the joint between the tub and surround and the vertical seams, you'll do better with a small tube of white kitchen- and- bath silicone caulk.
To apply this caulk successfully, use only what's necessary to fill the joint, and don't wait longer than about 4. Apply a 1. 2- to 1.
If you find that you've applied too little, wait several hours and fill in the voids with a touchup application.
- Read about how the MagnaPanel access panel hardware system solves many problems encountered in the construction and installation of tile, tubs, and fixtures.
- An acrylic tub and shower surround may not have the sex appeal of an enameled cast iron tub and an elegant ceramic tile surround, but it's a lot easier to keep clean.
- Bathtubs - tub walls - MAAX: Products list. Installation; Shape; Style; Unique Features; Ariosa. 1 Tub - 2 Pieces; Pin System; Showers. NEW.
- When it comes to alternatives, you can choose from new tile, plastic tub surround kits and professionally installed solid-surface panels. A quick look at.
- The experts at the DIYNetwork.com show how to install a marble tile floor as a tub surround.
Problems With Shower Surrounds. Shower surrounds not only look aesthetically pleasing but also are easy to clean and provide the protection to your bathroom walls so.
Tub surrounds and shower surrounds are easy to install and maintain. Follow our ten steps to update your bathroom with a surround. Installation can vary from product. Looking to have a new bathtub or shower liner installed to give your bathroom a makeover? Explore the many installation options offered by The Home Depot. How to Install a Tub Surround. Bathtub surrounds protect the walls from moisture. They may, however, become stained or discolored with age. You can give your bathroom.